N10-009 · Network Implementation

Configure switching technologies and features

Objective 2.2 · Given a scenario, configure switching technologies and features.

7 learning blocksNext unfinished block 1 · about 15 minutes12 key conceptsOriginal practice · Review pending
ProgressNot started0/7 blocks learned and checked
Learn

Start your lesson

Study the required lesson for each block, then take its short check. Guided exercises are optional. Required case practice within the blocks counts toward the readiness checklist, not lesson completion.

0/7blocks complete
Your notesPrivate to you
Up to 1,000 characters. Active writing time is recorded; idle time is excluded.
Block 1 of 7

Access VLAN · VLAN trunk · Native VLAN

Next · 15 min

Required provider lesson

Study the lesson below before taking this block's check.

Optional concept notes

Access VLAN

Assigns untagged endpoint traffic to one VLAN on a switchport.

VLAN trunk

Carries traffic for multiple VLANs across one link.

Native VLAN

Carries untagged frames on an IEEE 802.1Q trunk.

Cross-certificationCCNA ↔ Net+

Native VLAN

The core idea stays the same. The surrounding objective changes the evidence, decision, or task the exam asks for.

Required block check · Block 1

Required for course progress · Pass with 3 of 3 correct

Your confirmation records study. Passing the check is still required for course progress.
Block 2 of 7

Understand LACP

7 min

Required provider lesson

Study the lesson below before taking this block's check.

Optional concept notes

LACP

Negotiates compatible links into one logical Ethernet channel.

Cross-certificationCCNA ↔ Net+

LACP

The core idea stays the same. The surrounding objective changes the evidence, decision, or task the exam asks for.

Required block check · Block 2

Required for course progress · Pass with 1 of 1 correct

Your confirmation records study. Passing the check is still required for course progress.
Block 3 of 7

Configure switching and prove the resulting state

18 min

No provider lesson is assigned to this block. Study the ITForMe lesson below, then take the required check.

Required ITForMe lesson
Concept brief · about 18 minutes with practice

Configure switching and prove the resulting state

By the end, you can
  • Restore a missing VLAN on a trunk while retaining the other allowed VLANs.
  • Check link-aggregation member consistency and protocol state.
  • Use spanning-tree root, role, cost, and state to explain forwarding paths.
  • Verify supported frame or packet size across the entire path.

Create VLANs before assigning access ports, and use an SVI only when the switch needs Layer 3 presence for management or routing. On an 802.1Q trunk, tagged VLANs must be allowed at both ends and the native VLAN treatment must agree. A voice VLAN can carry tagged phone traffic while the attached PC remains in the untagged access VLAN. Link aggregation requires compatible members and a common negotiation mode.

Spanning tree prevents Layer 2 loops by choosing a root and placing redundant paths into nonforwarding roles. Speed and duplex mismatches produce characteristic counters. MTU must be supported across the entire path; enabling jumbo frames on one hop only creates size-dependent loss. Read show vlan, interface/trunk, aggregation, spanning-tree, and counter output as a sequence rather than issuing configuration blindly.

Optional support
Worked example
Situation

Users in VLAN 30 fail across a new trunk. Output shows VLAN 30 exists and access ports are correct, but the trunk allowed list contains only VLANs 10 and 20.

Reason it through

The VLAN database and access membership are proven; the allowed list is the first failed forwarding dependency.

Expected result

Add VLAN 30 to the allowed list without replacing existing entries, then verify it is forwarding on both trunk ends.

Optional practice
Reasoning self-check

Users in VLAN 30 fail across a new trunk. Output shows VLAN 30 exists and access ports are correct, but the trunk allowed list contains only VLANs 10 and 20.

  1. Record the observed state and separate facts from assumptions.
  2. Use the supplied evidence to evaluate VLAN and trunk output, Link aggregation evidence, Spanning-tree output, and End-to-end MTU.
  3. Choose the least disruptive valid action, then predict the output or traffic change it should produce.
Compare your reasoning
Expected answers
  • Add VLAN 30 to the allowed list without replacing existing entries, then verify it is forwarding on both trunk ends.
  • The conclusion cites the decisive observation rather than the answer label alone.
If you got stuck
  • If two answers seem possible, identify which one changes a variable that the scenario already held constant.
  • If evidence is insufficient, name the next command, counter, record, or controlled substitution needed.

Compare your reasoning with the revealed answers if helpful. The block check below is required for course progress.

Hands-on lesson practice

Work through the scenario

Practice simulation

Use the case evidence to complete the tasks, then check objectives. Terminals list their supported syntax under Command help.

Practice limits and saved work

Guided practice is optional. You can start required case practice directly; it counts toward the readiness checklist. Neither exercise completes the lesson or its checkpoint. Checks evaluate the supplied scenario and modeled configuration, not live systems or traffic. Work is saved in this browser session. Human technical review is pending.

Optional guided practice

Place a printer in its VLAN

Create VLAN 35 named PRINT and place Gi0/8 in it as an enabled access port, then save.

  • PRINT-SWswitch
  • Printerendpoint
Objectives
  1. VLAN 35 exists with name PRINTpending
  2. gigabitethernet0/8 is enabled as an access port in VLAN 35pending
  3. Configuration is savedpending
AtlasOS 4.2 training simulatorIOS-style practice syntax
Browser simulator
Report an issue with this exercise

Your report is private to you and the review team because lesson exercises can contain answers.

Required case practice

Required for the readiness checklist · Pass at 100%

Required case practice

Repair a desk port

A replacement desk on Gi0/18 requires VLAN 42 USERS, but the supplied state shows trunk mode and VLAN 24. Write the corrected command sequence.

  • DESK-SWswitch
  • Deskendpoint
Objectives
  1. VLAN 42 exists with name USERSpending
  2. gigabitethernet0/18 is enabled as an access port in VLAN 42pending
  3. Configuration is savedpending
AtlasOS 4.2 training simulatorIOS-style practice syntax
Browser simulator
Report an issue with this exercise

Your report is private to you and the review team because lesson exercises can contain answers.

Technical references

Required block check · Block 3

Required for course progress · Pass with 3 of 4 correct

This records your study. Passing the check is still required for course progress.
Block 4 of 7

Trace a host to its VLAN gateway

18 min

No provider lesson is assigned to this block. Study the ITForMe lesson below, then take the required check.

Required ITForMe lesson
Concept brief · about 18 minutes with practice

Trace a host to its VLAN gateway

By the end, you can
  • Apply diagnose vlan database and svi state to the supplied evidence.

A host reaches an SVI only if its access port belongs to the VLAN, every intervening trunk carries that VLAN, and the SVI has an active Layer 2 member plus correct Layer 3 addressing.

Virtual Local Area Network (VLAN): Creates a logical Layer 2 broadcast domain independent of physical switch location; traffic crosses VLANs only through a Layer 3 function.

VLAN database: Records VLAN identifiers and local attributes on a switch; creating a VLAN does not automatically assign access ports or permit it on trunks.

Switch virtual interface (SVI): Is a logical Layer 3 interface associated with a VLAN, used for switch management or inter-VLAN gateway routing when the VLAN and line protocol are active.

Optional support
Worked example
Situation

PC-A is 192.0.2.10/24 on switch port Gi1/0/8 configured access VLAN 30. VLAN 30 exists on SW1 but not SW2. The trunk allows 10,20,30. SW2 has interface Vlan30 at 192.0.2.1/24, currently down/down.

Reason it through

The access port classifies PC-A frames into VLAN 30 and the trunk permits tag 30, but SW2 lacks VLAN 30 in its VLAN database. The SVI therefore has no active VLAN and stays down. Creating VLAN 30 on SW2 supplies the missing Layer 2 state; changing the host mask would not.

Expected result

After VLAN 30 exists and is active on SW2, the SVI comes up and PC-A can ARP for 192.0.2.1.

Optional practice
Reasoning self-check

Changed state: VLAN 30 now exists on both switches and trunks allow it, but SW2 Vlan30 is administratively shutdown.

  1. Mark each boundary as pass/fail and name the single missing state that explains the SVI status.
  2. Identify the exact supplied observation contradicted by the peer proposal.
Compare your reasoning
Expected answers
  • Enable the SVI, then verify line protocol, ARP, and gateway reachability; recreating the VLAN is no longer the fix.
  • Corrected-answer reference: Access membership passes; trunk allowance passes; SW2 VLAN database fails. Add/activate VLAN 30 on SW2, then verify SVI up and ARP/ping to 192.0.2.1.
If you got stuck
  • If the SVI remains down, verify that at least one VLAN-30 Layer 2 port or trunk is operational; an administratively enabled SVI alone does not guarantee line protocol up.

Compare your reasoning with the revealed answers if helpful. The block check below is required for course progress.

Technical references

Required block check · Block 4

Required for course progress · Pass with 1 of 1 correct

This records your study. Passing the check is still required for course progress.
Block 5 of 7

Decode a phone port and broken aggregate

20 min

No provider lesson is assigned to this block. Study the ITForMe lesson below, then take the required check.

Required ITForMe lesson
Concept brief · about 20 minutes with practice

Decode a phone port and broken aggregate

By the end, you can
  • Apply repair tagging and aggregation from evidence to the supplied evidence.

An access port can carry untagged workstation traffic in a data VLAN and tagged phone traffic in a voice VLAN. A trunk tags allowed VLANs except its native VLAN. Aggregated members must agree on speed, duplex, VLAN mode, and aggregation state.

Native VLAN: Carries untagged frames on an 802.1Q trunk by convention; native-VLAN mismatch can leak traffic or create confusing control-plane behavior.

Voice VLAN: Lets an access port place an attached phone's voice traffic in a separately signaled VLAN while a connected workstation remains in the data access VLAN.

802.1Q tagging: Adds a VLAN identifier and priority information to Ethernet frames across a trunk; endpoints on ordinary access ports normally send untagged frames.

Link aggregation: Combines compatible physical links into one logical bundle for capacity and resiliency; member settings and aggregation protocol state must agree.

Speed: Defines the physical signaling rate negotiated or configured at each end; incompatible settings can leave a link down or operating below design capacity.

Duplex: Controls simultaneous transmit and receive behavior; a duplex mismatch can leave link up while causing collisions, errors, and poor throughput.

Optional support
Worked example
Situation

A phone tags voice frames VLAN 40 and passes an untagged PC on data VLAN 20. SW1's two-link LACP trunk uses native VLAN 99 and allows 20,40,99. SW2 uses native VLAN 1; member 2 is forced 100/full while the other links negotiate 1000/full. Users see intermittent loss and native-VLAN warnings.

Reason it through

The edge behavior is correct: untagged PC frames map to VLAN 20 and phone-tagged frames to 40. The uplink has two independent faults: native VLAN disagreement changes the meaning of untagged frames, and the speed mismatch prevents member 2 from joining a coherent aggregate.

Expected result

Set native VLAN 99 at both ends and make both LACP members 1000/full with identical trunk settings; verify both members bundled and VLANs 20/40 pass.

Optional practice
Reasoning self-check

Independent review case: Edge: data VLAN 20, voice VLAN 40. SW1 Po1: LACP, native 99, allowed 20,40,99, two 1-Gbps members. SW2 Po1: LACP, native 1; member 1=1000/full, member 2=100/full. New evidence: a peer submitted this change for approval: Data 20; native voice 40; matching LACP members

  1. State how PC and phone frames are classified, then list both uplink corrections and the counters/state that prove them.
  2. Identify the exact supplied observation contradicted by the peer proposal.
Compare your reasoning
Expected answers
  • Reject the submitted change. Required finding: The phone sends tagged voice traffic in VLAN 40 while the attached PC sends untagged data in VLAN 20. Making voice native does not preserve the stated tagging design. Then provide the corrected decision and its direct verification.
  • Corrected-answer reference: PC untagged->20; phone tagged->40. Match native VLAN 99 and member speed/duplex/trunk parameters; both members must show bundled and error counters must stop rising.
If you got stuck
  • If only one member bundles after speed correction, compare allowed VLANs and LACP mode/key on that physical member before changing endpoint VLANs.

Compare your reasoning with the revealed answers if helpful. The block check below is required for course progress.

Technical references

Required block check · Block 5

Required for course progress · Pass with 1 of 1 correct

This records your study. Passing the check is still required for course progress.
Block 6 of 7

Calculate tunnel payload and path MTU

18 min

No provider lesson is assigned to this block. Study the ITForMe lesson below, then take the required check.

Required ITForMe lesson
Concept brief · about 18 minutes with practice

Calculate tunnel payload and path MTU

By the end, you can
  • Apply compute usable mtu through encapsulation to the supplied evidence.

An IP MTU is the largest complete IP packet, including its IP header, that an interface can carry without IP fragmentation. Link framing is additional. Encapsulation consumes part of the outer path MTU, so endpoints may need a smaller inner MTU even when every Ethernet segment supports 1500-byte IP packets.

Maximum transmission unit (MTU): The IP MTU is the largest complete IP packet, including its IP header, that fits the link without fragmentation. Ethernet framing overhead is outside the IP packet; tunnel headers consume space within the outer path's MTU.

Jumbo frames: Use an Ethernet payload larger than the common 1500-byte IP MTU, often near 9000 bytes, and require consistent endpoint, switch, and path support.

Optional support
Worked example
Situation

An IPv4 tunnel crosses a 1500-byte path and adds 60 bytes outside each inner IP packet. A host sends a 1500-byte inner packet with DF set. Small probes work; the large packet is dropped and ICMP fragmentation-needed is filtered.

Reason it through

The outer packet would be 1560 bytes, exceeding the path MTU by 60. DF prevents IPv4 fragmentation and filtered ICMP breaks path-MTU feedback. The maximum inner IP packet is 1500-60=1440 bytes. For a 20-byte IPv4 plus 20-byte TCP header, maximum TCP data per segment is 1400 bytes.

Expected result

Use inner MTU 1440 (or TCP MSS 1400 for the stated headers) and allow required ICMP feedback. A 1440-byte inner packet produces a 1500-byte outer packet.

Optional practice
Reasoning self-check

Changed path: outer IP MTU 1492, tunnel overhead 60, inner IPv4 header 20 and TCP header 32.

  1. Calculate maximum inner IP packet and TCP data sizes, then explain why a one-switch jumbo setting cannot repair this path.
  2. Identify the exact supplied observation contradicted by the peer proposal.
Compare your reasoning
Expected answers
  • Inner MTU=1432 and TCP MSS=1380.
  • Corrected-answer reference: Inner MTU=1440; TCP MSS=1400 for the given headers. Restore PMTUD feedback or set compatible endpoint/tunnel sizes. Jumbo on one hop does not change the 1500-byte bottleneck.
If you got stuck
  • If you got 1460, you subtracted only TCP/IP headers and ignored tunnel overhead; if you got 1340, you likely subtracted the 60 bytes twice.

Compare your reasoning with the revealed answers if helpful. The block check below is required for course progress.

Technical references

Required block check · Block 6

Required for course progress · Pass with 1 of 1 correct

This records your study. Passing the check is still required for course progress.
Block 7 of 7

Predict spanning-tree forwarding

16 min

Required provider lesson

Study the lesson below before taking this block's check.

For this block: Resolve the root and safe forwarding roles from bridge IDs and path costs. If you have already studied this lesson, you can go to the check.

Optional ITForMe notes and practice
Optional ITForMe teaching · about 16 minutes with practice

Predict spanning-tree forwarding

By the end, you can
  • Apply resolve a layer 2 loop to the supplied evidence.

Spanning tree elects the lowest bridge ID as root. Each nonroot switch selects its lowest-cost path toward that root; redundant ports that would complete a loop remain nonforwarding until topology changes. Rapid Spanning Tree Protocol (RSTP) keeps this loop prevention while allowing faster reconvergence than classic STP. An alternate port provides another path toward the root; rapid transitions use protocol agreement and current port roles, rather than simply forwarding every redundant link.

Spanning tree: Elects a root and places redundant Layer 2 ports into forwarding or nonforwarding roles to prevent loops, then reconverges when topology changes.

Optional support
Worked example
Situation

SW1 bridge ID 24576:...01 connects to SW2 and SW3 at cost 4. SW2 bridge ID 32768:...02 and SW3 32768:...03 also have a cost-4 link between them.

Reason it through

SW1 has the lowest bridge ID and becomes root. SW2 and SW3 each use their direct cost-4 link toward SW1. Their mutual link would close a triangle; the side with the inferior advertised root path/bridge tie-break is nonforwarding. If a root link fails, that alternate can transition according to the protocol.

Expected result

SW1 is root, both direct root links forward, and one end of SW2-SW3 is nonforwarding; no broadcast frame can circulate indefinitely.

Optional practice
Reasoning self-check

Independent review case: Triangle: SW1-SW2 cost 4, SW1-SW3 cost 4, SW2-SW3 cost 4. Bridge IDs: SW1=24576:01, SW2=32768:02, SW3=32768:03. New evidence: a peer submitted this change for approval: All three links forward because each has equal cost.

  1. Elect the root, identify each nonroot root port, and explain why the third link cannot forward at both ends.
  2. Identify the exact supplied observation contradicted by the peer proposal.
Compare your reasoning
Expected answers
  • Reject the submitted change. Required finding: That creates a Layer 2 loop and broadcast amplification. Then provide the corrected decision and its direct verification.
  • Corrected-answer reference: SW1 is root; SW2 and SW3 select their direct SW1 ports; one SW2-SW3 endpoint blocks/discards. On failure, verify reconvergence rather than disabling spanning tree.
If you got stuck
  • If you chose the highest bridge ID, remember the election prefers the lowest priority/MAC bridge ID; bandwidth influences path cost after root election.

Compare your reasoning with the revealed answers if helpful. The block check below is required for course progress.

Technical references

Required block check · Block 7

Required for course progress · Pass with 2 of 2 correct

Your confirmation records study. Passing the check is still required for course progress.
Optional recap

Review this lesson

Use only this lesson's worked example and key concepts for a quick self-check.

  1. Restate the worked example in your own words.
  2. Name the lesson concepts that explain the result.
  3. Explain why the closest alternative does not fit.
Your next milestone

Check the whole objective

This unlocks objective 2.2 for recall. The latest checkpoint needs 70% or higher; a lower result puts the lesson back near the front of your timeline.

Complete the lesson checks first.A score of 70% or higher advances the course. Today shows the remaining requirements for your daily goal.
Official blueprint references
Official Network+ certification and objectives overviewCompTIA ↗Official Network+ N10-009 V9 exam objectivesCompTIA ↗
Report an issue with this lesson

Your report is private to you and the review team because lesson exercises can contain answers.